Designation: D – 11Standard Test Methods for Field Measurement of Surface These test methods are under the jurisdiction of ASTM Committee D01 on. There are two ASTM standards that deal with surface profile assessment, D , Standard Test. Methods for Field Measurement of Surface Profile of Blast. 18 Oct For hot-dip galvanizing applications, it is possible to measure and verify the steel surface profile according to ASTM D, Standard Test.
|Published (Last):||9 August 2015|
|PDF File Size:||20.70 Mb|
|ePub File Size:||11.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
Standards for Measurement of Surface Profile There are currently four primary standards for measurement of surface profile in astm d 4417 surfaces.
Only the use of surface profile depth micrometers and replica tape were updated, and the specification changes are as follows:. Standards for Measurement of Surface Profile.
The surface profile must be compatible with the coating system. Link to Active This link will always route to the current Active version of the standard. The measurements must conform to the minimum and maximum surface profile requirements listed in the astm d 4417 specification.
Save my name, email, and website in this browser for xstm next time I comment. Leave a Reply Cancel reply Your email address will not be published. Both the structure and the coating system protecting the structure will move while in service. For hot-dip galvanizing applications, it is possible to measure and verify the steel surface profile according to ASTM D, Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel, prior to application of repair materials where the surface has been prepared via power tool or abrasive blast cleaning x.
Updates to ASTM D4417
According to ASTM D, a minimum of 2 readings is obtained per area; the average of the two readings is reported.
ASTM D4417 – 14
According to ASTM D, a minimum of 10 readings is obtained per area; the maximum surface sstm is reported discarding obvious outliers. Historical Version s – view previous versions of standard.
Peak density the xstm of peaks per unit area also plays a key role in maintaining adhesion of the coating system and provides greater resistance to corrosion undercutting when the coating system gets damaged while astm d 4417 service.
ASTM D contains astm d 4417 methods of measuring surface profile depth: What is Surface Profile and Why is it Necessary? So, in effect the reading on the micrometer or the RTR from the replica tape represents several xstm and valleys, while the depth micrometer does not.
This movement may be caused by expansion and contraction of the substrate due to temperature fluctuation, or live loads placed onto astm d 4417 structure; for example, traffic crossing a bridge. There are currently four primary standards for measurement f surface profile in steel surfaces. The values adtm in parentheses are for information only. Visual Comparator – This test method, as well as the comparator discs available on the market, have stayed the same, and therefore astm d 4417 were no updates for this test method.
Your email address will not be published. Larger repair areas or prepared hot-dip galvanized surfaces for painting can be measured with 10 readings taken from a minimum of three, 6×6 inch 15×15 cm areas.
Today, Method B astm d 4417 Method C are the astm d 4417 commonly used, so that is what x will be focusing on. Profile depth designations are based on the concept of mean maximum profile h max ; this value is determined by averaging a given number usually 20 of the highest peak to lowest valley measurements made in the field of view of a standard measuring microscope.
October 18, Asmt by Alana Hochstein. The three test methods described within D for measuring surface profile include visual comparators, surface profile depth micrometers, and replica tape.
While both the depth micrometer and replica tape methods conform to ASTM D, the measurement acquisition principles are quite different. S by Alana Hochstein. Work Item s – proposed revisions of this standard. This includes personalizing content and advertising. This is done because of evidence that coatings performance in any one small area is primarily influenced by the highest surface features in that area and not by the average roughness. The standard does not address discarding outliers, but an update to the standard addressing outlier readings is planned.
Replica Tape – Although the technology has remained mostly constant for replica tape astj its atsm, industry research has addressed the sufficient number of readings required to achieve an accurate astm d 4417. When astm d 4417 project specification simply invokes ASTM D and not a specific method, the results of the surface profile measurements may differ when two different methods are used on the same project, even on the same surface and within the same area i.
Instead, recording astm d 4417 the highest reading when using a depth micrometer astm d 4417 closely matches the same measurements produced using replica tape.
Updates to ASTM D | American Galvanizer’s Association
Asym can be discussed and agreed upon 441 the pre-construction conference. The instruments described are readily portable and sufficiently sturdy for use in the field. During abrasive blast cleaning, the mass of the abrasive and the velocity of the abrasive movement created by compressed air generates kinetic energy the abrasive can reach speeds of over miles per hour astm d 4417 it exits the blast nozzle.
Same Surface, Different Results? This method can be used to measure the surface profile depth that is created by abrasive blast cleaning or impact-type power tools. There are additional techniques suitable for laboratory use not astm d 4417 by these test methods. These changes reflect industry research on current tooling asttm revealed averaged measurements are consistently less than the values obtained using replica tape.
Difference in Surface Profile Measurements: ASTM D Method B vs CKTA University
Typically, the higher the coating thickness the greater the surface profile depth. Larger repair areas or prepared hot-dip galvanized surfaces for painting can be measured with two readings taken from a minimum of three, 6×6 inch 15×15 cm areas. Therefore, differences are inevitable, particularly atm deeper surface profiles, and the results may or may not fall within astm d 4417 specified range for one of the two methods.
For measurements that fall between adtm sizes, it is still required that two readings using each tape are to be averaged to comprise one reading i.